Home > exterior plastic wall cladding > should backer board be glued down for shower walls

should backer board be glued down for shower walls

How to Install Adhesive Tub or Shower Surround Panels

But because the panels are glued, the walls need to be clean so that the adhesive will make good contact. Walls that are damaged will also need to be patched first. After cleaning and repairing the wall surfaces, remove all the handles and trim work for the tub and shower valves.

Do You Install the Wallboard Before Installing the Shower Pan

Wallboard needs to have an expansion joint of 1/8 inch around the perimeter of the shower and between each board. This is to allow for movement of the studs. The wallboard must be installed 1/8

Does Backerboard Need Sealant? | Hunker

Should you decide to use sealant over backerboard, there are a few points to keep in mind. Liquid sealants must be applied thickly enough over the entire surface to provide complete coverage, which means multiple coats. As with any porous surface, liquids can be soaked up and leave some areas unprotected unless several layers are laid down.

Best Types of Tile Backer Board for the Shower

But with many non-organic shower backer boards available as alternatives, there is little reason to use greenboard. Plywood: Plywood alone cannot be used as a substrate under tile in showers. Some homeowners believe that painting or priming plywood will render it suitable to use as shower/tub backer board. This is not true.

Installing Cement Backer Board - Ask the Builder

Cement backer board is the best thing to install in your bath or kitchen if you want to make sure your tile stays on the wall. Cement backer board resembles the actual cement mud slathered on walls by the master tile setters of old. Cement is waterproof. Great video here!

Hardiebacker Board - Which Adhesive | TilersForums.com

Evening all, Ive just ordered hardiebacker board to install in bathroom. Wall - Will be installed directly onto existing masonry Floor - Will be installed on to 18mm WBP, with a further sub floor of 18mm WBP beneath. I have read conflicting information with regards to which adhesive is best

How to Install Cement Backer Board for Ceramic Tile

Cement board is used for most floor tile and has all but replaced plywood and drywall backer materials for wall-tile applications in wet areas, like showers and tub surrounds. Cement board forms a durable, stable base for tile, and it has no organic materials (unlike drywall, greenboard, or plywood) so it is not prone to mold, rot, shrinkage

Selecting a Backer Tile Board (DIY) | Family Handyman

Cement board is the most durable, trouble-free tile backer for tub surrounds, showers, floors and all other wet areas. Its made from cement and sand, and is reinforced by fiberglass mats on both sides, so it's impervious to water.

bathroom - Hardie Board Subfloor—Thinset or No? - Home

I stripped out the old flooring down to the 1x8 wood planks (about 1/4" between each). I have 1/4" Hardie Board to put down in preparation for tile and I'm a little confused on how I should do this. Some resources I've found have said to lay down mortar first, then screw the board into the floor.

Cement Board Installation on Floors- Avoid These 5 Mistakes

Cement board seams require mesh tape and thinset 1. No Thinset underneath the backer board. Just the other day, I saw a video featuring someone fastening Hardibacker directly to the subfloor with nothing underneath it.

Do You Install the Wallboard Before Installing the Shower Pan

Wallboard needs to have an expansion joint of 1/8 inch around the perimeter of the shower and between each board. This is to allow for movement of the studs. The wallboard must be installed 1/8

Does Backerboard Need Sealant? | Hunker

Should you decide to use sealant over backerboard, there are a few points to keep in mind. Liquid sealants must be applied thickly enough over the entire surface to provide complete coverage, which means multiple coats. As with any porous surface, liquids can be soaked up and leave some areas unprotected unless several layers are laid down.

Frequently Asked Questions | Resource Center | James Hardie

Yes, HardieBacker 1/4'' cement board may be used in a shower. However, we recommend HardieBacker 500 if you need to make a smooth transition to drywall. The board must be mechanically fastened every 8'' on center to the wood or metal studs spaced a maximum of 16'' on center.

Backer board for shower surround? : HomeImprovement

Backer board for shower surround? So I'm looking at installing something like the link below, however it says to glue it up over drywall. Obviously that's a terrible idea because eventually the silicone will leak and then I have wet drywall.

Installing Backer Board: When is it Necessary | DoItYourself.com

If you have had to remove part of the wall in order to add electrical cables, or do some plumbing, you can repair small holes by installing backer board. Obviously, this is not a suitable repair for load bearing walls, but if you need to put kitchen cabinets or shower heads onto the wall, then adding a backer board is a good idea.

Installing Cement Backer Board - Ask the Builder

Cement backer board is the best thing to install in your bath or kitchen if you want to make sure your tile stays on the wall. Cement backer board resembles the actual cement mud slathered on walls by the master tile setters of old. Cement is waterproof. Great video here!

Selecting a Backer Tile Board (DIY) | Family Handyman

Cement board is the most durable, trouble-free tile backer for tub surrounds, showers, floors and all other wet areas. Its made from cement and sand, and is reinforced by fiberglass mats on both sides, so it's impervious to water.

How to Use Plastic Bead Board as a Shower Surround | Hunker

A recent product, plastic bead board, is an effective mold-resistant product to use as a shower surround. It is a durable exterior product that is made of PVC and has the appearance of wainscoting. Plastic bead board is less expensive than tile and more durable than thin plastic inserts.

bathroom - Hardie Board Subfloor—Thinset or No? - Home

I stripped out the old flooring down to the 1x8 wood planks (about 1/4" between each). I have 1/4" Hardie Board to put down in preparation for tile and I'm a little confused on how I should do this. Some resources I've found have said to lay down mortar first, then screw the board into the floor.

No thinset under cement board - BiggerPockets

Just went to inspect some work and noticed they weren't using thinset to lay down the cement board under porcelain tile. When I asked the contractor, he asked his flooring guy who had been doing tile for 25 years and "never puts thinset under cement board". Our agreement was to put down cement board and tile.

Do You Install the Wallboard Before Installing the Shower Pan

Wallboard needs to have an expansion joint of 1/8 inch around the perimeter of the shower and between each board. This is to allow for movement of the studs. The wallboard must be installed 1/8

Does Backerboard Need Sealant? | Hunker

Should you decide to use sealant over backerboard, there are a few points to keep in mind. Liquid sealants must be applied thickly enough over the entire surface to provide complete coverage, which means multiple coats. As with any porous surface, liquids can be soaked up and leave some areas unprotected unless several layers are laid down.

How to Prep and Install DIY Bathroom Shower Tile | Lowe's

You don't need to use a backer board in the entire bathroom, just in the wet shower area. Choose a backer board that's the same thickness as the drywall so you have a seamless transition from one to the other. Measure the work area and cut your boards to fit. To cut a backer board, mark the board, score it with a knife and snap it along the

Backer board for shower surround? : HomeImprovement

Backer board for shower surround? So I'm looking at installing something like the link below, however it says to glue it up over drywall. Obviously that's a terrible idea because eventually the silicone will leak and then I have wet drywall.

Installing Backer Board: When is it Necessary | DoItYourself.com

If you have had to remove part of the wall in order to add electrical cables, or do some plumbing, you can repair small holes by installing backer board. Obviously, this is not a suitable repair for load bearing walls, but if you need to put kitchen cabinets or shower heads onto the wall, then adding a backer board is a good idea.

Installing a Shower Pan Liner - Extreme How To

The pre-measured liner needs to lap up the sides of the shower walls at least 9 inches. It is nailed to the framing studs of the shower near the top of the lapped edge. If it is necessary to seam together two pieces of material, a special solvent can be used to glue them together to form a single waterproof liner.

How to Use Plastic Bead Board as a Shower Surround | Hunker

A recent product, plastic bead board, is an effective mold-resistant product to use as a shower surround. It is a durable exterior product that is made of PVC and has the appearance of wainscoting. Plastic bead board is less expensive than tile and more durable than thin plastic inserts.

Selecting a Backer Tile Board (DIY) | Family Handyman

Cement board is the most durable, trouble-free tile backer for tub surrounds, showers, floors and all other wet areas. Its made from cement and sand, and is reinforced by fiberglass mats on both sides, so it's impervious to water.

HardieBacker Cement Board Ultimate Backer Board Guide

should be installing backer board. * Most local building codes REQUIRE the use of a backerboard or underlayment under tile in wet areas such as bathtub or shower surrounds. Projects Where Backer Board or Underlayment Should Be Used • Renovating bathroom • Updating kitchen • Replacing basement walls • Installing fireplaces, furnaces, and

No thinset under cement board - BiggerPockets

Just went to inspect some work and noticed they weren't using thinset to lay down the cement board under porcelain tile. When I asked the contractor, he asked his flooring guy who had been doing tile for 25 years and "never puts thinset under cement board". Our agreement was to put down cement board and tile.

Installing Backer Board: When is it Necessary | DoItYourself.com

If you have had to remove part of the wall in order to add electrical cables, or do some plumbing, you can repair small holes by installing backer board. Obviously, this is not a suitable repair for load bearing walls, but if you need to put kitchen cabinets or shower heads onto the wall, then adding a backer board is a good idea.

Selecting a Backer Tile Board (DIY) | Family Handyman

Cement board is the most durable, trouble-free tile backer for tub surrounds, showers, floors and all other wet areas. Its made from cement and sand, and is reinforced by fiberglass mats on both sides, so it's impervious to water.

HardieBacker Cement Board Ultimate Backer Board Guide

should be installing backer board. * Most local building codes REQUIRE the use of a backerboard or underlayment under tile in wet areas such as bathtub or shower surrounds. Projects Where Backer Board or Underlayment Should Be Used • Renovating bathroom • Updating kitchen • Replacing basement walls • Installing fireplaces, furnaces, and

How to Use Plastic Bead Board as a Shower Surround | Hunker

A recent product, plastic bead board, is an effective mold-resistant product to use as a shower surround. It is a durable exterior product that is made of PVC and has the appearance of wainscoting. Plastic bead board is less expensive than tile and more durable than thin plastic inserts.

bathroom - Should I use Kerdi membrane or cement backerboard

All shower/tub areas should have concrete board (I prefer hardiboard). Whether or not you need a Kerdi membrane is a factor of use. In normal residential use I wouldn't worry about it. Backerboard plus a waterproofing membrane like Redgard is all that is needed for tub surrounds with thinset then tile. Kerdi really offers very little advantage

Diamondback Tile Backer: the superior tile substrate

Diamondback® Tile Backer and Diamondback Tile Backer Type X Boards are used in wet areas, non-wet areas, high-humidity areas and are typically used for adhering ceramic tiles to walls and floors in bathrooms, in shower and tub enclosure walls, kitchens, laundry and utility rooms.

How to Install a Cement Backer Board Over a Plywood Subfloor

1. Lay down full sheets of backer board where they will fit first. You must first dry-lay the entire floor with cement board before adhering and nailing the floor down.

How to Thin Set Cement Board to Plywood for Tile Installation

Cement-based backer board stabilizes the plywood substrate and provides a flat, even surface for tile. For best results, especially on floors, concrete board should be installed at least one day

Sticking 6mm cement board to floorboards prior to tiling

Hello, I have the whole downstairs of my house to tile, 60m2. I have old floorboards down currently and I am thinking of sticking 6mm 1200x800 hardie backer cement board prior to tiling, what I need to no is what's the best thing to stick the cement board with to the floorboards, a tile adhesive or a special type of glue?

tile - How do I remove Cement Board that has been screwed in

If it was glued down with construction adhesive you might be in for a more miserable time. Safety glasses, gloves, and a sledgehammer to get started. You'll probably have to break the board around the screws and remove them with locking pliers - the screwheads will be full of thinset and it would be tedious to get them to the point you can use

HardieBacker Cement Board Ultimate Backer Board Guide

should be installing backer board. * Most local building codes REQUIRE the use of a backerboard or underlayment under tile in wet areas such as bathtub or shower surrounds. Projects Where Backer Board or Underlayment Should Be Used • Renovating bathroom • Updating kitchen • Replacing basement walls • Installing fireplaces, furnaces, and

bathroom - Should the backer board be in front of or behind

Because the backer board tends to bow out when 'lipped' over the tub flange, you should: Install the tub Install shims on the studs to 'pad out' the backer so that it just clears the tub flange and overhangs it a bit (but doesn't 'land' on the rim of the tub) but leaves a 1/4 to 3/8 inch gap to the tub.

USG Durock Brand Cement Board Installation Guide (English

bond than fiber-cement boards or bare plywood, USG Durock ® cement board is an outstanding backerboard for a wide variety of reasons. Choose this high-performance alternative to fiber-cement boards or bare plywood surfaces for: Superior Tile Bond Prevents tile pops and grout cracks, up to 40% greater tile bond than fiber-cement board.

Diamondback Tile Backer: the superior tile substrate

Diamondback® Tile Backer and Diamondback Tile Backer Type X Boards are used in wet areas, non-wet areas, high-humidity areas and are typically used for adhering ceramic tiles to walls and floors in bathrooms, in shower and tub enclosure walls, kitchens, laundry and utility rooms.

installing a pvc shower liner - the space between

So if your shower pan is 3′ x 3′ buy a liner that is 4′ x 4′. If you have a bench you will want the liner to go up and over the bench and then up the wall again about 6 inches … so you do the math. 🙂 Our shower pan is about 4′ x 4′ with an 18″ high bench and I bought a liner that was 5′ x 7′, and it worked out.

Tub Surround and Shower Adhesive - Liquid Nails

LIQUID NAILS ® Tub Surround & Shower Wall Adhesive (LN-915) provides an exceptional waterproof bond under extreme conditions and won't harm most tub surrounds and shower walls. Light color won't show through surrounds. Recommended for most plastic tub and shower enclosures. Sizes: 10 oz. Cartridge. Coverage: 30 Lineal ft. Using 1/4" Bead

Shower Leaking: 5 signs your shower is built to fail | DIYTileGuy

Seems like it should go under the board and the tile…much the same way as in your prev. response to me if the floor tile should go under the tile/backer board on the wall or flush…you replied under. The rep. said maybe I should hire a builder to answer my questions…she said they only install showers, not tile.

SimpleSet White 1 Gal. Pre-Mixed Thin-Set Mortar - The Seven Trust

Suitable for some wet areas such as tub surrounds and shower walls; Heating Mat for Tile and Glue-Down Floors types of stone to cement backer board. For

tile - How do I remove Cement Board that has been screwed in

If it was glued down with construction adhesive you might be in for a more miserable time. Safety glasses, gloves, and a sledgehammer to get started. You'll probably have to break the board around the screws and remove them with locking pliers - the screwheads will be full of thinset and it would be tedious to get them to the point you can use

Installing Ceramic Tile Over Different Floor Surfaces

Installing ceramic tile over vinyl or linoleum surfaces can be more complicated than expected and probably should be avoided whenever possible. However, if you can't remove the old surface or otherwise decide to install over it, lay a backer board with thin-set over the old surface to serve as your new subfloor material.

bathroom - Should the backer board be in front of or behind

Because the backer board tends to bow out when 'lipped' over the tub flange, you should: Install the tub Install shims on the studs to 'pad out' the backer so that it just clears the tub flange and overhangs it a bit (but doesn't 'land' on the rim of the tub) but leaves a 1/4 to 3/8 inch gap to the tub.

Tub Surround and Shower Adhesive - Liquid Nails

LIQUID NAILS ® Tub Surround & Shower Wall Adhesive (LN-915) provides an exceptional waterproof bond under extreme conditions and won't harm most tub surrounds and shower walls. Light color won't show through surrounds. Recommended for most plastic tub and shower enclosures. Sizes: 10 oz. Cartridge. Coverage: 30 Lineal ft. Using 1/4" Bead

How to Install Backer Board | how-tos | DIY

Using a notched trowel, apply a leveling bed of thinset mortar over the subfloor and embed the backer board sheets into the adhesive. Spread the mortar to about 3/16" thickness. Add more mortar as necessary to fill sunken areas in. Lay the backer board according to the manufacturer's instructions.

Which side goes down on durock? - AskingLot.com

Foam Tile Backer Boards More recently, USG Durock foam board, Laticrete Hydroban Board, and Johns Manville GoBoard have all come on the market. There are some big advantages to these panels for showers: They are lightweight and don't damage the walls as you carry them into the house and upstairs.

The $50 Stone Shower DIY {your pick} - Picklee

Use tile adhesive to carefully glue down each stone to the shower wall. This process requires a lots of patience. Mark explained that his wife would come home from work and do a 2″ x 36″ section each night! Once the stones are glued down and dry, apply a layer of grout on top.

backer board vs waffer board - selfhelpforums.com

If you are dealing with walls use 1/4" blue board [moisture resistant drywall]. Then imperfections are obsobed by the blue board drywall and that drywall is easily removed from that wall removing the tile with it if you wish to remodel later. Hope this gives you some words of thought Good Luck Wg This wa

Hardi backer board over concrete in bathroom? - DoItYourself

HardieBacker board must be installed in accordance with local building codes and the floor must be engineered not to exceed the L/360 deflection criteria, including live and dead design loads, for the specific joist spacing used. HardieBacker board is not designed for use over concrete. "- HARDIEBACKER™ BACKERBOARD - FAQ

Shower Leaking: 5 signs your shower is built to fail | DIYTileGuy

Seems like it should go under the board and the tile…much the same way as in your prev. response to me if the floor tile should go under the tile/backer board on the wall or flush…you replied under. The rep. said maybe I should hire a builder to answer my questions…she said they only install showers, not tile.

tile - How do I remove Cement Board that has been screwed in

If it was glued down with construction adhesive you might be in for a more miserable time. Safety glasses, gloves, and a sledgehammer to get started. You'll probably have to break the board around the screws and remove them with locking pliers - the screwheads will be full of thinset and it would be tedious to get them to the point you can use

Shower Wall Panels - Onyx Collection

Onyx wall panels are available in any height, color, and design. Panels are available in Gloss, Matte, Tile, and Wavy Tile finish. An Onyx panel is approximately 5/16" thick and is a solid color throughout. Panels weigh about 3.5lbs per square foot. Shower Wall Panel Instructions (PDF)